Monthly Archives: December 2014

Juan Correa Final Project LED Arcade Controller Nov-Dec 2014

Below is a PDF I uploaded of all my labs for the final project I hope they can be viewed. I created in word but It did copy and paste as intended in the post. MTEC2280 Juan Correa Arcade Controller … Continue reading

Posted in Uncategorized | Leave a comment

Interactive Picture Frame: Project Documentation

Objective:¬†Document the project, report the problems encountered and how we solved them. Materials: Photo, Glass, Arduino Uno, Adafruit ‚ÄúMusic Maker‚ÄĚ MP3 Shield for Arduino, HC-SR04 Ultrasonic Distance Measuring Senso Module for Arduino, Male DC Power Plug to 9v Battery Button … Continue reading

Posted in Uncategorized | Leave a comment

Sam Yannotti Final lab post

Objective:¬†To create an Arduino based tone generator run with a passive low pass filter Materials:¬†Arduino Uno board & programming software, an unbelievable amount of wires, piezo buzzer (or a better pair of speakers), breadboard, variable resistors, 1uf capacitor Methods: 1) … Continue reading

Posted in Uncategorized | Leave a comment

12/16/2014 Ben, Michael, Sabin

Objective: Make stepper motors move using a patentiometer and printing/fixing the connectors between mini par and stepper motor. Materials:¬†stepper motor, Blender, Mini Par, stepper motor, computer, Makerbot, Arduino. Methods:¬†Using new measurements fix the plastic conectors fit the stepper motor and … Continue reading

Posted in Uncategorized | Leave a comment

12/15/2014 Sabin Visan

Objective: Make connectors between two stepper motors and Mini Par Materials: stepper motor, Blender, Mini Par.  Methods: Use measurements from Mini Par and stepper motor to create custom connectors between them. Data:  Results: Made two connectors between stepper motor and Mini Par. Discussion: 

Posted in Uncategorized | Leave a comment

12/11/2014 Ben and Sabin

Objective:¬†Making stepper motor move and controlling Rover using Xbox 360 controler Materials:¬†stepper motor, arduino mega, stepper motor shield, power supply, computer, rover and Xbox 360 controler. Methods: Use computer code to determine how the steper motor will move, make steper … Continue reading

Posted in Uncategorized | Leave a comment

BoByBot (12/11/14)

Objective: Creating the shield for our robot. Materials: Computers, makerbot, pliers, robot, smart phone. Methods: We are using the makerbot software to make/design a shield for our robot. Data:¬† Results: Were still working with the makerbot software, our shield should … Continue reading

Posted in Uncategorized | Leave a comment

Darya Dubouskaya: Lab report 12/9.

Finally, I was able to upload a code from this recourse: http://maxoffsky.com/maxoffsky-blog/how-to-play-wav-audio-files-with-arduino-uno-and-microsd-card/ and connect it to arduino with micro sd card shield(lcsoft.net SD module card shield). Card shield is connected and talking to the arduino. Reading and writing files. I … Continue reading

Posted in Uncategorized | Leave a comment

BoByBot 12/9/14

Objective:¬†To measure our robots length and width, so we can figure out the size for the shield our robot is going to have. We are also going to start making the shield for BoByBot. Materials:¬†The chassis, ¬†3 wheels, screw drivers, … Continue reading

Posted in Uncategorized | Leave a comment

BoByBot (12/4/14)

Objective:¬†Today we are testing out our robot again and seeing if after we fixed the controls, our robot will move better and more foward, without any issues. Materials:¬†¬†The chassis, 3 wheels, screw drivers, cables, wire cutters, arduino/bread board, the motor, … Continue reading

Posted in Uncategorized | Leave a comment